HOW TO CLEAN PUCH MOPED BODY FULL
HOW TO CLEAN PUCH MOPED BODY LICENSE
HOW TO CLEAN PUCH MOPED BODY SERIES

On those the brake light needs to be 6V 21W in order to have good spark with the brakes on. Or it can be for some US model mopeds with a special вЂњexternal ignition groundвЂќ that powers the brake light. This can be for a brighter brake light on battery powered motorcycles. The bulb holder is made for a вЂњlarge glassвЂќ upper bulb. 9417 is for mounting higher up on the rear fender.Д¬EV 9400.1/9401.1/9417.1: These are the same except for the bulb holder and upper bulb. Both bulbs are the Ba15s вЂњsmall glassвЂќ type. Top is brake light and bottom is tail light.

HOW TO CLEAN PUCH MOPED BODY SERIES

CABLES 100's are illustrated and specifiedД¬EV 9400/9401/9417: In 1977 these вЂњrectangularвЂќ series dual-bulb lamps came out.

Hardware: metric bolts screws, nuts, washers.

Pedals, cranks, pins freewheels, tensioners.

Wheel parts: bearings axle and brake parts.

Shocks, seats, fenders and other frame parts.

Engine Hardware: special nuts, pins, keys, shims, clips.

HOW TO CLEAN PUCH MOPED BODY LICENSE

Locks, helmets, baskets license plate brackets oils, sprays, foot pegs.So far my speed tests show about a 12mph increase with a top speed around 47mph. The clutch needs a bit of tweaking when I get more time. The bike is a dream come true and really rips. I had the whole frame sand blasted and powder coated gloss black. New angel eye head light, off road tires, and temp indicator. I put on a MLM side bleed expansion pipe for more power. I re-geared the bike to have good low end power. A new light weight crank shaft was installed for higher revs and a new clutch for better acceleration. The bike was switched over to a 100w magneto with electronic ignition system. I machined the lower cases to match the new air intake channels. I rebuilt the motor and bumped the displacement to 64ccвЂ™s and installed a larger 15mm carb. I upgraded the suspension to off road suspension, it lifted the bike a good 3-4вЂќ higher than its previous stance. I decided on a gun metal gray paint as I wanted the bike to have an enduro motorcycle look. I then found a friend who owns an auto body shop to paint the tank and a few spare parts. I found a guy in California that would repair the dents in the tank, one of the few people that does this in the US. I started this process by breaking the bike down and stripping it to the frame. I thought why not see what I can make of this moped. I had some time and I was looking for a project. I was strapped for time while in school, so I did the bare minimum to get it back together but I always had a dream of restoring it.ДЇast forward to 2016. I dented the tank pretty good, broke the head light, bent a pedal arm, and screwed up the controls. I was banged up, the bike was banged up, and I limped it home by shutting the ignition on and off as I went down the hill to control my speed. The throttle cable had become pinched in the steering column. And soon I was going to be crumpled into the back of a yellow VW bug! I ditched the bike and slid down the road.

HOW TO CLEAN PUCH MOPED BODY FULL

I let go of the throttle but nothing happened, the moped continued on full speed ahead. I hit the the throttle hard and took off, but traffic started to come to a stop. One day when I was riding home between classes, I got stuck in traffic. It was great for commuting and zipping around town.

I rode my new moped up the big hill to campus and around town with a smile ear to ear. I cleaned and tuned it up just in time for my junior and senior year of college. When I purchased the bike it was in good condition. I purchased this bike from a close friendвЂ™s dad who bought it new from a motorcycle shop in Chapel Hill, North Carolina.

How to clean puch moped body